Apcemmert Metal Fabricators All articles
Procurement & Specification

Maintainability by Design: Specifying Bespoke Metalwork for Its Working Life

Apcemmert Metal Fabricators
Maintainability by Design: Specifying Bespoke Metalwork for Its Working Life

Photo: Leadingtopunion, CC0, via Wikimedia Commons

Bespoke metalwork is often procured for a service life measured in decades, yet the people who will inspect, repaint and repair it are seldom in the room when the drawings are agreed. The maintenance handover should not be a folder passed over at practical completion. For UK trade buyers, maintainability is a design input, and the procurement stage is the last practical point at which it can be influenced without costly rework.

Begin with the maintenance task, not the finish

A useful starting point is to list the tasks that will be carried out on the fabricated asset: routine visual inspection, intrusive examination of welds and connections, cleaning, coating repair, fastener replacement, drainage clearance and, in some cases, removal of a component for refurbishment. For each task, the specification should identify who will carry it out, how often, and what access they will need.

If an inspection can only be completed from a mobile elevating work platform, that is a recurring cost and a scheduling constraint. If a connection can only be reached by erecting scaffolding, the maintenance regime becomes heavier than it needs to be. Designing out unnecessary temporary works is preferable to writing a method statement for them. Where access is unavoidable, the design should provide safe, agreed points for it rather than leaving the maintenance contractor to improvise.

Make inspection points visible and reachable

Critical details should not be hidden behind closed boxes or sealed assemblies. Inspection cover plates, removable panels and openings for boroscope access allow condition to be checked without destructive intervention. On external steelwork, hidden faces and back-to-back angles are common locations for coating breakdown and water trapping; if they cannot be inspected, they cannot be maintained predictably.

Access should be considered at the drawing stage, not after fabrication. A removable panel is of limited value if its fasteners require a specialist tool or if the panel weight exceeds a single-person lift. Similarly, a drainage path that discharges into an inaccessible hollow section merely moves the problem. The specification should state the inspection philosophy and require the fabricator to demonstrate that it can be delivered.

Bolted or welded: choose for the maintenance regime

Welded connections are durable and often appropriate for permanent structure, but they are not easily reversed. Bolted connections allow components to be removed, replaced or adjusted, provided the fasteners can be reached and torqued correctly. For wear items, future equipment interfaces and panels that may need periodic replacement, bolted detailing is usually the more maintainable choice.

The decision is not only structural. Bolted interfaces introduce crevices and dissimilar metal contacts that require protection and, in external UK conditions, a galvanic corrosion check. Fastener assemblies should be specified with the maintenance regime in mind, including the need for retorquing and the risk of seizure. The operations and maintenance information should record torque values, fastener grades and any isolation details so that replacement does not become a trial-and-error exercise.

Drainage and water trapping

Water is a persistent adversary of external metalwork. Ledges, upward-facing channels, unsealed hollow sections and poorly detailed joints all collect moisture and debris. The drawing should show where water will go and how it will leave. Weep holes, falls and sealed caps are simple measures, but they must be positioned where they can be cleared.

For galvanized components, vent and drain holes serve both the coating process and the service life of the item. Their size and position should be agreed with the galvanizer and shown on the fabrication drawing. Drainage details that are added at the workshop are rarely recorded in the handover information, which makes future inspection less reliable.

Plan the coating repair route

No coating lasts indefinitely. The specification should identify the intended repair system and the conditions under which it can be applied. For hot-dip galvanized steel, zinc-rich repair coatings are commonly used for local damage; for painted systems, compatible touch-up materials and colour references should be recorded. The maintenance team needs to know what is on the steel, not merely what colour it is.

Design details should support repainting as well as initial application. Sharp edges, narrow gaps and surfaces that cannot be reached with a brush or roller will be poorly protected in later years. Rounded edges, sensible clearances and accessible faces reduce the labour involved in coating repair. The coating specification, including any references to BS EN ISO 12944 or equivalent system data, should be carried through to the handover pack.

Specify the handover information, not just the hardware

Trade buyers should require operations and maintenance information as a contractual deliverable. At minimum, this should include as-built drawings, a component schedule, fastener and torque details, coating system data sheets, repair procedures, inspection intervals, access requirements, lifting points, component weights and a removal sequence for any item likely to be replaced.

This information is most useful when it is prepared for the person who will actually use it. A drawing that shows every weld but not how to remove a bearing housing is of limited value. A schedule that lists a proprietary component without its supplier or reference is equally frustrating. The O&M pack should be reviewed before handover, not after the maintenance team first encounters a problem.

Agree maintainability before fabrication

A maintenance review held before fabrication drawings are released is a low-cost exercise. It can confirm access, removal routes, drainage and coating repair details while changes are still made in the drawing office rather than on site. The review should be minuted and the outcomes incorporated into the approved drawings. At Apcemmert Metal Fabricators, bespoke work is detailed with the understanding that the finished item will be inspected and maintained long after it leaves the workshop. That perspective belongs in the specification, not in the handover folder.

All Articles

Related Articles

Cut to Fit the Job: Selecting Profiling Methods for Bespoke Metal Components

Cut to Fit the Job: Selecting Profiling Methods for Bespoke Metal Components

The Route to Site Is Part of the Design: Logistics-Led Detailing for Bespoke Steelwork

The Route to Site Is Part of the Design: Logistics-Led Detailing for Bespoke Steelwork

Setting Out in Someone Else’s Building: Survey and Tolerance Control for Retrofit Metalwork

Setting Out in Someone Else’s Building: Survey and Tolerance Control for Retrofit Metalwork