An Allowance, Not an Alibi: Specifying Adjustment in Bespoke Metalwork Interfaces
Photo: Roy, William, 1726-1790, Public domain, via Wikimedia Commons
Bespoke metalwork seldom meets a perfect host structure. Even where surveying, setting out and fabrication have been handled competently, small deviations accumulate between the drawing office and the installed condition. The final interface often carries the consequence. A bracket that was detailed to land neatly on a column flange may arrive to find the flange out of position by a few millimetres; a balustrade base plate may sit on a slab edge that is neither level nor square. The question is not whether adjustment will be needed, but whether it has been designed deliberately or improvised on site.
That distinction matters commercially. Adjustment designed into the package is a controlled allowance with a stated range, a defined locking method and a clear inspection route. Adjustment improvised after delivery is usually a sequence of elongated holes, unplanned packers and informal agreements that are difficult to price, inspect and defend. For UK trade buyers, the objective is to secure the first while preventing the second from becoming an alibi for poor setting out.
Where adjustment belongs
Adjustment should be considered at the interfaces where bespoke metalwork meets something else: base plates to holding-down bolts, brackets to primary steel, balustrade posts to slab edges, subframes to structural openings, and equipment supports to plinths or plant decks. These are the points where construction tolerances, survey uncertainty and minor movement meet the fabricated item.
It is useful to separate three conditions at the drawing stage. The first is erection tolerance: the practical allowance needed to assemble components that have been fabricated within reasonable limits. The second is host-structure tolerance: the deviation inherent in the concrete, steel or masonry to which the metalwork connects. The third is in-service movement: thermal expansion, deflection, settlement or vibration that the connection must accommodate over its working life. They are related, but they are not interchangeable. A slotted hole introduced for erection may be inadequate for long-term movement, while a movement joint detailed for thermal range may be unnecessary and costly at a simple cover fixing.
Setting a range that means something
An instruction to provide 'slotted holes to suit site' is not a specification. It transfers an undefined risk to the fabricator and gives the site team no basis for checking whether the delivered item is adequate. A more useful specification states the adjustment range, its direction and the datum from which it is measured. For example, a bracket may require plus or minus 15 millimetres horizontally and plus or minus 10 millimetres vertically, with a packer range of 0 to 25 millimetres beneath the base plate.
The fabricator should then demonstrate that the detail works at the extremes, not only at the nominal position. Bolt edge distances, bearing area, washer coverage and tightening access all need to be checked with the bolt at each end of its slot. A slot that is theoretically long enough but leaves a structural washer overhanging the plate is not an adjustment allowance; it is a non-conformance waiting to be discovered. Where connections are designed for friction grip or other controlled bolt behaviour, the effect of slotted holes on the connection's performance must be resolved by the designer, not left to site preference.
Adjustment zones should appear on the general arrangement drawings and on the fabrication drawings. A schedule of interfaces, listing the permitted range, the locking method and the inspection point, is more reliable than a note on a single detail. It also gives the buyer a document against which to compare tenders. A bidder who has allowed for a defined range is pricing a different scope from one who has allowed for a nominal fit and hopes for the best.
Packers, shims and cover plates
Packers and shims are not incidental consumables. Their material, thickness range, compressibility and corrosion resistance should be appropriate to the location. External packers in exposed UK conditions need particular attention, especially where dissimilar metals or trapped moisture could create a maintenance issue. Grouting beneath base plates should be detailed so that the packer arrangement does not create voids or prevent proper support.
Cover plates deserve the same consideration. A cover plate that conceals an elongated hole can improve appearance and protect the connection, but only if it is designed as part of the assembly. If it traps water, interferes with inspection or cannot be removed without damaging the finish, it has solved one problem and created another. Cover plates should be shown on the drawings, fixed by a stated method and included in the finish specification.
Movement is not erection tolerance
In-service movement requires a different design response from installation adjustment. A sliding connection, a clearance around a fixing or a movement joint is intended to allow controlled displacement over time. An oversized hole used to bring a misaligned component together is not. Mixing the two can produce details that are either too loose in service or too tight to install.
Where movement is expected, the design should state the direction, magnitude and frequency of that movement, together with the limits of the connection. The fabricator can then detail bearings, clearances and restraints accordingly. The site team should know which fixings are to be finally tightened only after alignment and which must remain free to slide. That information belongs in the installation instructions, not in a site conversation after the access equipment has been stood down.
Access and locking
The best adjustment detail fails if nobody can reach it. Tool access for spanners, torque wrenches and socket sets should be checked at the drawing stage, particularly in recessed locations, behind cladding or close to adjacent steelwork. Hand access for placing packers and washers matters as well. A connection that can only be adjusted before a neighbouring component is installed is not adjustable in any practical sense.
Locking methods should be specified rather than assumed. Structural washers, plate washers, locking plates, grout and torque-controlled tightening all have a place, but they are not interchangeable. The specification should say how the adjusted position is held, how it is inspected and whether the fixing is to be tightened at installation or after final alignment. Where a connection may need future adjustment, access should be maintained and the method recorded. Burying an adjustment detail behind a sealed cover is acceptable only if the design accepts that it will not be adjusted again.
Governance against the alibi
Adjustment becomes an alibi when it is used to absorb errors that should have been corrected earlier. A survey that reveals a significant deviation from the drawings is a design issue, not a reason to run every slot to its limit. The project should define who surveys, when the survey is compared with the fabrication drawings, and what happens if the two do not agree. Hold points before cover-up, photographic records of adjusted positions and a simple as-built note are proportionate measures for packages where interfaces are complex.
For a trial piece or first-of-type assembly, the adjustment range can be tested before full production. That is often more valuable than a drawing review alone, because it exposes access, packing and locking difficulties that a nominal detail hides.
In 2026, UK buyers are working under familiar programme pressure, and the temptation to treat adjustment as a site matter remains. It is cheaper to resolve at the drawing stage. A stated range, a workable access route and a defined locking method turn adjustment into a controlled part of the package. They do not excuse poor setting out; they make sure that the last few millimetres are designed, priced and inspected rather than discovered.